Managing Editor, Leeham News & Analysis

Scott Hamilton

Jet engines degrade in normal operating conditions compared with new deliveries. Challenging environments accelerate the degradation of parts and, with this, fuel efficiency.
In the Middle East, for instance, fine dust particles are especially hard on engines. But degradation also occurs in “normal” environments, as well as super-cold ones.
Volcanic ash can cause catastrophic failure, such as with the 1982 incident in which a British Airways Boeing 747 with Rolls-Royce engines flew unknowingly at night into a high-altitude ash cloud. All four engines shut down due to ash ingestion and significant damage.
The crew was finally able to restart the engines as the jumbo jet glided toward what seemed like a certain water ditching. The plane made a safe emergency landing.
Dust doesn’t have remotely the same effect. Its degradation to the engine occurs over time.
These issues have prompted GE Aerospace to develop a new foam engine power wash that cleanses the engine. The company presented the technology to reporters in a media briefing on May 19.
For an Airbus A320neo airliner with a CFM International Leap-1A engine, the wash takes about four hours. Typical intervals for an active maintenance program are about every 250 to 500 cycles. Widebody engines take longer, at about eight hours.
The foam wash replaces a water washing process that’s been around for decades. Pratt &amp; Whitney introduced its water wash system in the early 1980s to clean JT8D engines used by Muse Air Corp’s McDonnell Douglas DC-9-50s and MD-80s.
GE’s foam system is currently used on only five commercial airliner engines: the CF34, Leap, GE90, GEnx, and the Engine Alliance GP7200 made by GE and PW. The science may be applied to smaller engines used on business jets.
<h2>Better Than Water Alone</h2>
The foam technology, which replaces a conventional water wash, uses two J-hooks at the front of the engine to spin the fan. This ensures that cleaning extends through to&nbsp;the aft stage of the compressor or the hot section. These sections need cleaning to restore the asset’s operational integrity.
GE’s foam is a specific chemistry that dissolves dust. It’s compatible with GE’s engine materials. The foam is injected into the aft stage of the compressor and systematically through borescope ports to remove debris that's built up there. The debris degrades the efficiency of that compressor over time.
GE wants to do this type of cleaning at the same time as other prescribed maintenance, so there’s no impact on the engine's utilization for the airline. The wash may occur with the engine on the wing.
Called 360 Foam Wash, the wash process leads to improved fuel economy from the engine’s degraded point, according to GE. An engine that’s running colder lasts longer, and it uses less fuel. It also extends the lifespan of key parts, improving durability.
Foam Wash has been licensed to more than 10 customers, including those in the Middle East and North America. SkyWest Airlines, which operates a fleet of Mitsubishi CRJs and Embraer E1s with the CF34, is one example. The same process could work for turbofans powering business jets.

News and developments about aircraft engines, including turbofan, turboprop, turboshaft and piston.

GE’s Jet Engine Foam Wash Prevents Damage and Reduces Fuel Burn

Turbofan wash cycle takes between four and eight hours

GE Aerospace’s 360 Foam Wash process can reverse damage to jet engines caused by factors such as dust and other factors found in harsh operating environments.

Engine Foam Wash Prevents Damage and Reduces Fuel Burn

2024 Corporate Aviation Leadership Summit

Charles Alcock

News and developments about airplanes, helicopters and unmanned air vehicles used in all varieties of operations, including airlines, military, business, commercial, general aviation and private.

News about environmental issues relating to aircraft operations, including noise issues, emissisions, and regulations. See Fuel for biofuel.

Hybrid version of Valo VTOL aircraft will have longer range and more payload

Vertical Starts Tests with Hybrid-electric Powertrain

Matt Thurber

News and issues relating to business, corporate and private aviation, primarily regarding turbine-engine-powered airplanes and helicopters. Subjects include aircraft, engines, maintenance, operations, personnel, acquisitions, accidents, safety, security, and training.

RTX business expects to create 200 new jobs by 2030

P&WC Opens Morocco Engine Parts Manufacturing Facility

Hanneke Weitering

News and issues concerning general aviation, specifically airplanes and helicopters powered by piston and alternative engines (i.e., non-turbine powered aircraft). Subjects include aircraft, engines, personnel, acquisitions, accidents, safety, security and training.

Air-cooled MagniAIR poised to benefit from MOSAIC rule

MagniX Debuts Electric Motor for Light Aircraft

Jessica Reed

News about simulators and training procedures, as well as workforce.

Satheeshkumar Kumarasingam will succeed Maria Della Posta when she retires June 1

Kumarasingam Named President of Pratt & Whitney Canada

Charlotte Bailey

 Support from France 2030 will help enable series production of propulsion system

French Funding Backs Ascendance’s Hybrid Propulsion System

Amy Wilder

News and issues about aviation maintenance, repair and overhaul (MRO), covering all segments of the aviation industry; and modifications for aircraft and engines. Subjects include product support of aircraft, engines and avionics, MRO company mergers, acquisitions, announcements and personnel, Airworthiness Directives, Supplemental Type Certificate approvals and other topics.

Dallas provider marks 10th year with expanded engine coverage

EAP Adds PW535E, Tay 611 to Maintenance Program

New developments and products in avionics, specifically about aircraft electronics in the cockpit.

Validation testing enables compatibility with Pro Line Fusion avionics

Blackhawk Expands XP67A Eligibility for King Airs

News about bills, laws, regulations and other governmental decisions affecting aviation and aerospace. Topics include FAA re-authorizations, taxes on fuel and aviation activities, environmental legislation, ICAO decisions, governmental mediation of labor conflicts and World Trade Organization disputes and decisions.

More In Engines